Electrical Hazards · Backup Power

UPS and Generator Backup Power Monitoring Solutions

UPS and generator backup power monitoring should be bounded by the dry contacts or confirmed communication interfaces that the existing equipment can provide. SFA acquires electrical parameters on the associated LV circuits, ESI acquires switch and operating status, ESX aggregates the data, and FEXLINK builds event and alarm records. Equipment protocols, transfer logic and maintenance windows must be verified during project design.

OVERVIEW

UPS and generator backup power monitoring should be bounded by the dry contacts or confirmed communication interfaces that the existing equipment can provide. SFA acquires electrical parameters on the associated LV circuits, ESI acquires switch and operating status, ESX aggregates the data, and FEXLINK builds event and alarm records. Equipment protocols, transfer logic and maintenance windows must be verified during project design.

The solution focuses on visibility of the backup power path and does not replace the UPS, the generator or their protection systems. Electrical parameters, dry contacts and a platform event chain help O&M staff distinguish utility supply, backup supply, the transfer sequence and load-side status.

Electrical HazardsBackup Power
UPS and Generator Backup Power Monitoring Solutions
BEFORE / AFTER

Before retrofit → With the solution

Before retrofit

  • Backup power status and the transfer sequence are not transparent
  • UPS, generator and switchgear data sit in separate systems, so event times are hard to align
  • Manual inspection alone cannot produce traceable operating and alarm records

With the solution

  • Brings backup power status into a single queryable event view
  • Reduces reliance on local indicators and manual enquiries to confirm the transfer sequence
  • Provides data for maintenance, fault review and later expansion
EFFECT ANALYSIS

How to evaluate the effect

01

Measurable signal

SFA monitors electrical parameters on LV circuits, ESI acquires dry contacts from the backup power source or switchgear, and ESP adds N-PE voltage monitoring where the site requires it.

02

Data source

SFA Multi-Parameter Electrical Controller · ESI Digital Status Monitor

03

Review method

Backup power sources, distribution circuits and dry contacts map one-to-one to the site point list

04

Acceptance boundary

This solution does not replace the control and protection functions of the UPS, generator, ATS or protective devices

STANDARDS

Applicable standards

Standards and protocols are listed for project applicability review; the final clause set and edition follow the project location, industry and contract.

Applicability of low-voltage installations references the GB/T 16895 series; the specific part and edition are confirmed per projectInterface and test requirements for the UPS, generator and transfer equipment are confirmed against equipment documentation and project design documentsCommunication protocols, point lists and platform interface versions are frozen before implementation
ACCEPTANCE

Acceptance and boundaries

  • Backup power sources, distribution circuits and dry contacts map one-to-one to the site point list
  • Status changes, voltage and current data and event times are traceable
  • Network-loss buffering and recovery upload are tested
  • Alarm grading, acknowledgement and closure procedures are reproducible
  • Connecting the monitoring system does not change the existing backup power protection and transfer logic
PAIN POINTS

Industry Pain Points

01

Backup power status and the tr…

Backup power status and the transfer sequence are not transparent

02

UPS, generator and switchgear …

UPS, generator and switchgear data sit in separate systems, so event times are hard to align

03

Manual inspection alone cannot…

Manual inspection alone cannot produce traceable operating and alarm records

ARCHITECTURE

Solution Architecture

Layered architecture, a complete data loop from sensing to operation.

UPS and Generator Backup Power Monitoring system topologyFour-layer data flow from perception and edge control to the platform and application layers for UPS and Generator Backup Power Monitoring.01Perception layer
SFA monitors electrical parameters on LV circuits, ESI acquires dry contacts from the backup…
02Edge / control layer
ESX handles data aggregation, time stamping and communication. It does not directly change U…
03Platform layer
FEXLINK builds the device register, status views, alarms, events and reports.
04Application layer
O&M staff check the supply path, transfer events, load status and alarm handling, and connec…
Perception layer
SFA monitors electrical parameters on LV circuits, ESI acquires dry contacts from the backup power source or switchgear, and ESP adds N-PE voltage monitoring where the site requires it.
Edge / control layer
ESX handles data aggregation, time stamping and communication. It does not directly change UPS or generator control logiccontrol authority is confirmed separately.
Platform layer
FEXLINK builds the device register, status views, alarms, events and reports.
Application layer
O&M staff check the supply path, transfer events, load status and alarm handling, and connect to existing monitoring systems where required.
CORE CAPABILITIES

Core Capabilities

Product 1

SFA Multi-Parameter Electrical Controller

Acquires voltage, current, power and energy on the associated LV circuits; the specific circuits and accuracy are confirmed by model

Product 2

ESI Digital Status Monitor

Acquires dry contacts and switch status available from the UPS, generator or switchgear

Product 3

ESP Neutral-Ground Voltage Monitor

Supplements monitoring where neutral-to-earth (N-PE) voltage matters for sensitive loads; this is not equivalent to monitoring the UPS itself

Product 4

ESX Smart Edge Computing Gateway

Aggregates field device data, performs edge buffering and upload; interface capacity is confirmed by specific model

Product 5

FEXLINK IoT Platform

Displays operating status, events, alarms and response records; the deployment mode is confirmed per project

DATA LOOP

Data Loop

The complete data value chain: sense -> data -> AI -> warning -> control -> operation.

01Site sensing
02Edge aggregation
03Platform analysis
04Alarm handling
05O&M closure
PRODUCT PORTFOLIO

Product Portfolio

Electrical Hazards

SFA Multi-Parameter Electrical Controller

SFA Multi-Parameter Electrical Controller

Acquires voltage, current, power and energy on the associated LV circuits; the specific circuits and accuracy are confirmed by model

Electrical HazardsBackup Power
Backup Power

ESI Digital Status Monitor

ESI Digital Status Monitor

Acquires dry contacts and switch status available from the UPS, generator or switchgear

Electrical HazardsBackup Power
Electrical Hazards

ESP Neutral-Ground Voltage Monitor

ESP Neutral-Ground Voltage Monitor

Supplements monitoring where neutral-to-earth (N-PE) voltage matters for sensitive loads; this is not equivalent to monitoring the UPS itself

Electrical HazardsBackup Power
Backup Power

ESX Smart Edge Computing Gateway

ESX Smart Edge Computing Gateway

Aggregates field device data, performs edge buffering and upload; interface capacity is confirmed by specific model

Electrical HazardsBackup Power
Electrical Hazards

FEXLINK IoT Platform

FEXLINK IoT Platform

Displays operating status, events, alarms and response records; the deployment mode is confirmed per project

Electrical HazardsBackup Power
CUSTOMER VALUE

Customer Value

Quantified, verifiable customer value.

Brings backup power status…

Brings backup power status into a single queryable event view

Electrical HazardsBackup Power

Reduces reliance on local …

Reduces reliance on local indicators and manual enquiries to confirm the transfer sequence

Electrical HazardsBackup Power

Provides data for maintena…

Provides data for maintenance, fault review and later expansion

Electrical HazardsBackup Power
RELATED SOLUTIONS

Related Solutions

Full Electrical Quantity Intelligent Monitoring for Low-Voltage Distribution Rooms

This scheme unifies the electrical parameters, trends and alarms of incoming, bus-tie, feeder and key circuits into a distribution-room view, and applies to new construction and phased retrofit.

Electrical HazardsFull Electrical Parameters

Data Center Cabinet and PDU Power Consumption Monitoring

The solution targets cabinet power visibility and anomaly location, avoiding describing ordinary circuit terminals directly as smart PDUs, and emphasizing dual-power supply and O&M boundaries.

Electrical HazardsRack Power Consumption

Industrial Park Multi-Tenant Power Distribution and Safety

The solution focuses on data isolation and layered O&M in multi-tenant scenarios, avoiding concentrating all enterprise and circuit data into one master table without permission boundaries.

Electrical HazardsStatus Visualization

Residual Current and Electrical Fire Monitoring

The solution is centered on continuous monitoring of leakage current and temperature, helping O&M detect change trends and form alarm records, and applies to distribution cabinets, terminal circuits, and key power-consuming areas.

Electrical HazardsResidual Current

Fault Arc Identification and Early Warning

The solution applies to specialized arc-risk investigation and pilot trials, not aiming at stacking algorithm metrics, but first establishing a verifiable sampling, alarm, and review process.

Electrical HazardsArc Fault

Distribution Cabinet Smart Circuit Breaker Retrofit

The solution targets terminal and branch distribution cabinets, using smart circuit breakers to replace or retrofit traditional branch protection, and establishing a unified entry point for circuit-level monitoring and control.

Electrical HazardsBranch Circuit Protection
FAQ

FAQ

No. Readability depends on the UPS model, communication card, protocol openness and authorization. Verification usually starts from dry contacts or the interface provided by the vendor.
Prefer the dry contact provided by the equipment, acquired by ESI. If more parameters are needed, a defined communication protocol and point list must be obtained.
By default it monitors in parallel (bypass) only; it is not wired into the transfer circuit. Any control connection must be reviewed separately and must preserve the existing backup power and protection logic.
ESP provides supplementary N-PE voltage monitoring. Whether it is needed depends on the sensitive loads and the distribution system; it is not part of the UPS interface.
Combine switch status, electrical parameters on key circuits and time stamps. The specific criteria are set by project design and site testing.
Whether data is buffered, and for how long, depends on the ESX configuration and storage conditions. Network loss, buffering and recovery upload should be tested before implementation.

Start UPS and Generator Backup Power Monitoring Journey

Contact us for detailed solutions, quotes and technical support.